WhatsApp
Specialised programming equipment

Module programming, coding and ADAS calibration in Dubai

Motormec programs, codes and calibrates control modules with specialised equipment: VCDS, VCP, Abrites AVDI, Autohex, Magicmotorsport FLEX, Xhorse VVDI Prog, Multi-Prog, VVDI2 and VVDI MB, plus signal simulators, decade boxes, an NVH kit and ADAS calibration equipment.

WhatsApp or call +971 52 567 1398

01

Diagnostic and coding interfaces

Alongside our dealer-level diagnostic software, these interfaces read, code and adapt control modules, and flash their software.

Ross-TechVCDS

Windows diagnostic software and interface for VW Group cars. It reads and clears fault codes in every control module, shows live data, runs output tests, and handles coding, adaptations and basic settings.

Used forVW, Audi, SEAT and Skoda diagnostics, coding and adaptations

VCP (VAG CAN PRO)

A VW Group diagnostic and coding interface. As well as coding and adaptations, it can flash control unit software from original update files and read and write module EEPROM data.

Used forVW Group coding and control unit flashing

AbritesAVDI

The Abrites vehicle diagnostic interface. With Abrites software it runs advanced diagnostics, module programming, coding, adaptations, key programming and module replacement across most European makes.

Used forModule replacement, coding and key programming across makes

MicrotronikAutohex II

A BMW and MINI programming and diagnostic system. It programs and codes modules across the E, F and G series, reads and writes ISN data for engine, gearbox and security modules, and handles CAS, FEM and BDC key and immobiliser work.

Used forBMW and MINI module programming, coding and immobiliser work

02

Programming and key tools

When a control module is replaced, has lost its data or needs keys added, its memory has to be read, written and matched to the car. These are the tools we use for that work.

MagicmotorsportFLEX

An engine and transmission control unit programmer. It reads, writes and clones ECU and TCU data over OBD, on the bench and in boot mode, without opening the unit for many supported modules, and corrects checksums when writing.

Used forECU and TCU data backup, cloning and replacement

XhorseVVDI Prog

A bench programmer for EEPROM, flash and microcontroller memory. It reads and writes the memory chips inside engine computers, immobilisers and instrument clusters, so module data can be backed up, repaired or transferred.

Used forEEPROM and microcontroller reading and writing

XhorseMulti-Prog

The successor to VVDI Prog. It reads, writes and clones ECU and TCU data on the bench, including many Bosch, Continental and Siemens units, and covers MCU and EEPROM chips from Renesas, NXP, Infineon and others.

Used forBench ECU and TCU cloning and chip-level programming

XhorseVVDI2

A key and immobiliser programmer. It reads and writes VW Group immobiliser data, learns new keys, and works with BMW CAS and BDC security modules.

Used forKey and immobiliser programming for VW Group and BMW

XhorseVVDI MB

A Mercedes-Benz key programmer. It reads key passwords, prepares new keys, and renews and writes the EIS ignition switch and ELV steering lock, without desoldering.

Used forMercedes-Benz key, EIS and ELV programming

03

Signal and test equipment

Programming only fixes software. To prove whether a sensor, a wire or a module is at fault, we test the circuit with known, measurable signals.

Signal generators

Produce a precise, known signal, such as a square wave at a set frequency or a set voltage, to feed into a circuit or module input and check how it responds.

Used forTesting module inputs and circuits

Signal simulators

Imitate the signal a real sensor would send, such as a crankshaft, camshaft or wheel speed sensor. If the fault disappears with a simulated signal, the sensor is the problem; if it stays, the wiring or module is.

Used forSeparating a faulty sensor from a faulty module

Signal analyzers

Capture and decode signals and network traffic, including CAN and other in-car networks, to show what modules are actually sending and receiving.

Used forNetwork and communication faults

Decade boxes

Substitute an exact, adjustable resistance in place of a sensor, such as a temperature sensor, to check that the wiring and the module read it correctly.

Used forTesting sensor circuits and module readings

NVH kit

Noise, vibration and harshness testing with accelerometers and a microphone connected to the scope. It records vibration and noise on a road test and matches them to engine speed, road speed or a wheel or shaft.

Used forFinding the source of noises and vibrations

04

ADAS calibration

Advanced driver assistance systems rely on cameras and radar that have to be aimed precisely.

ADAS calibration equipment

Calibrates the cameras and radar sensors behind driver assistance features such as lane keeping, adaptive cruise control and automatic emergency braking. Calibration is needed after a windscreen replacement, a wheel alignment, a sensor replacement or accident repair.

Used forDriver assistance camera and radar calibration

Alongside

Dealer-level diagnostics

Diagnostics
Diagnostic tools at Motormec
ToolWhat it doesMakes
Dealer-level diagnostic softwareFull module access, guided fault finding, coding and adaptations, at the same depth as a main dealer, for every brand we work on.Porsche, Audi, Volkswagen, Bentley, Lamborghini, BMW, Mercedes-Benz, Range Rover
AbritesSpecialist software for module programming and coding.Most European makes
PicoScopeAn automotive oscilloscope. We measure sensor, actuator and network signals directly, so we see faults a scan tool never logs.Any car

Updated

FAQ

Programming and calibration questions

Can you program and code a replacement control module?

Yes. We program and code replacement modules with VCDS, VCP, Abrites AVDI, Autohex, Magicmotorsport FLEX and Xhorse VVDI Prog and Multi-Prog alongside our dealer-level diagnostic software.

Can you program keys for a Mercedes, VW Group car or BMW?

Yes. We use Xhorse VVDI MB for Mercedes-Benz keys, EIS and ELV, and Xhorse VVDI2 and Abrites AVDI for VW Group and BMW keys and immobilisers.

Do you do ADAS calibration in Dubai?

Yes. We calibrate driver assistance cameras and radar sensors, for example after a windscreen replacement, wheel alignment, sensor replacement or accident repair.

What is a signal simulator used for?

A signal simulator imitates a real sensor's signal. If the fault goes away with the simulated signal, the sensor is faulty; if it stays, the problem is in the wiring or the module.

What is an NVH kit?

NVH stands for noise, vibration and harshness. The kit uses accelerometers and a microphone with the scope to record a noise or vibration on a road test and trace it to its source.

Do you do ECU tuning?

No. We use programming tools to back up, repair, clone and replace control modules, not to tune engines.

WhatsApp first

Need a module programmed?

Message us on WhatsApp with the car, the module and what has already been tried.

Warehouse 4, Street 22, Al Quoz Industrial Area 3, Dubai · Mon–Sat 8:00 am to 6:00 pm, lunch 1 to 2 pm